bookingpolt.blogg.se - Apple configurator 2 restore

#Apple configurator 2 restore update#
#Apple configurator 2 restore full#
#Apple configurator 2 restore pro#
#Apple configurator 2 restore mac#

After initial Phase of iBoot restoer (SoCrom) there will be issued a reset signal which cuts external power supply.

#Apple configurator 2 restore mac#

Target Mac has charged and functional battery.Do not use the left port closest to track pad for power - you will need this for data. Target Mac (one that is being put in DFU) is connected to power.USB-C cable which supports data, USB A to C cable, or Thunderbolt 3 cable.a host Mac which has minimum OS of 10.13.5, Apple Configurator 2.6 or newer installed (from App Store), and an internet connection.Check trackpad on vaterdamaged devices before doing DFU Restore.

#Apple configurator 2 restore full#

Most boards require touchpad, some boards require Touchpad + Touchbar for full restore. THIS WILL BRICK THE MAC AND YOU WILL HAVE TO DO THE WALK OF SHAME TO AN APPLE STORE. The half that is unsuccessful, is, I'm sure because of a damaged trace or something like that - however, with it being in recovery, or Failure State B, it's much harder to diagnose.ĭO NOT DFU IF TARGET MAC IS ON BETA SOFTWARE. It seems half the time, after I fix Failure A, that I am able to get out of Failure B after restore. There have been many cases, where the unit came in with liquid damage, clearly a Failure State A type of situation, but the client attempted to restore before sending it, making it into a Failure State B. At this point, if you find you're short on PP3v3_G3H and remove it, you would have to restore again and PRAY that it works. Now you're at Failure State B, it makes it 10x harder to diagnose Failure State A, simply because you can't follow the power structure anymore. At this point, it would fail, and you would be stuck in recovery, let's call this Failure State B. Now you're in Failure State A, and you decided to force the unit into DFU, and attempt a restore. You plug it into another unit, to check if its in DFU mode. If you have a board that comes in, with no power. The problem is, if you fail a DFU restore, you may end up in a different error state than your original issue. There are many things that can cause a DFU restore to fail. Rule out parts or any other board issue that is possible before DFU restoring the unit. The moral of the story here, is before you attempt a DFU restore, for something that could be T2, attempt to rule out everything else before the restore, as you could brick the unit, and be in a worse condition. Obviously this way the unit won't functional properly. I tied IPD_LID_OPEN to SMC_LID_RIGHT to put a bandaid on the situation. I attempted a restore, this did not work. I replaced U4580, which fixed the camera, however the SMC_LID_RIGHT line was brought even lower to. Causing the unit not to fully wake when raising the lid (did respond when lid was closed) The camera also did not work, which lead me to U4850.

2: (820-01958) SMC_LID_RIGHT was low - 1v1 instead of the 1v8 it should be.

1: LID_OPEN_LEFT, LID_OPEN_RIGHT, and IPD_LID_OPEN would all function properly when triggered, however the unit would not sleep when lid closed.

Battery communication lines being pulled down - but not short causing battery not being recognized and not charging.

However, rule out other possibilities first! It is hard to tell why, but many devices stuck in G3H/T2 state are being repaired after revive.Įssentially anytime you see something that communicates with T2 not function, a DFU restore may resolve. One of weirdly common reasons for currupt BridgeOS firmware is corroded TouchID connector.

waterdamage on TouchID / Power button connector.

Revive is enough to perform CleanME, so if you swapped CPU for data recovery, you can first backup with Target Disk mode, then try revive and full boot. Whis will put uninitialized ME image to BridgeOS partition.

CPU / PCH replacement: since ME+EFI image is located on BridgeOS partition, to do classical "clean ME" procedure after PCH swap, you need to do full DFU restore.

Looping apple logo with no loading bar after waterdamage on power button (820-00850 confirmed case).

Unable to successfully create computer account and log in after erasing and reinstalling (M1 computers specifically).

Unable to boot into the current OS Internet Recovery using command + option + R.

#Apple configurator 2 restore update#

Failed macOS upgrade/reinstall/Security Update.

#Apple configurator 2 restore pro#

2023 A2780 16" M2 Pro / M2 Max MacBook ProĭFU mode is needed to restore the T2 firmware when:.3.5 Few things from experience: (Ed Hallman / crumblenaut)Īll MacBooks starting with T2 support this feature.3.4 Few things from experience: (Dusten Mahathy).3.3 Few things from experience (Liminalsunset):.3.2 Few things from experience (inwerp):.3.1.1 100% direct DFU mode using jumper.